Technicolor Thomson Flat Panel Television 27LCDB03B User Manual

1. IMPORTANT SAFETY INSTRUCTIONS  
Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if  
improperly handled. This product has been engineered and manufactured with the highest priority on safety. But  
IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to prevent  
potential danger, please observe the following instructions when installing, operating and cleaning the product. To  
ensure your safety and prolong the service life of your LCD TV product, please read the following precautions  
carefully before using the product.  
1.Read instructions—All operating instructions must be read and understood before the product is operated.  
2.Retain instructions—These safety and operating instructions must be kept in a safe place for future reference.  
3.Observe warnings—All warnings on the product and in the instructions must be observed closely.  
4.Follow instructions—All operating instructions must be followed.  
5.Water and moistureDo not use this product near water -  
for example, near a bathtub, washbowl, kitchen sink, or laundry  
tub, in a wet basement, or near a swimming pool, and the like.  
Do not use immediately after moving from a low temperature to  
high temperature environment, as this causes condensation,  
which may result in fire, electric shock, or other hazards.  
Moisture in rooms where the set is installed should not exceed  
85% humidity  
Leave the condensation to evaporate before turning the TV on  
again.  
6.Cleaning  
Unplug this product from the wall outlet before  
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a  
damp cloth for cleaning.  
Clean the screen with a glass care cleaner and the rest of the set  
with a soft cloth and neutral detergent. Regularly dust the vents  
at the back and sides. Using solvents, abrasive or alcohol based  
products risk damaging the TV.  
Caution : the screen of your LCD TV may be damaged if it is  
cleaned with strong detergents, alcohol or abrasive products.  
7.Ventilation—The vents and other openings in the cabinet are  
designed for ventilation. Do not cover or block these vents and  
openings since insufficient ventilation can cause overheating  
and/or shorten the life of the product. Do not place the product  
on a bed, sofa, rug or other similar surface, since they can block  
ventilation openings. This product is not designed for built-in  
installation; do not place the product in an enclosed place such  
as a bookcase or rack, unless proper ventilation is provided or  
the manufacturer’s instructions are followed.  
8.Heat sources—Keep the product away from heat sources  
such as radiators, heaters, stoves and other heat-generating  
products (including amplifiers).  
The TV components are sensitive to heat. The maximum  
ambient temperature should not exceed 350 celsius.  
9.Power cord protection—The power cords must be routed properly to prevent people from stepping on them  
or objects from resting on them. Check the cords at the plugs and product.  
Power-supply cords should be routed so that they are not likely to be walked on or snagged by items placed upon or  
against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the  
product.  
1
 
20.StandDo not place the product on an unstable trolley,  
stand, tripod or table. Placing the product on an unstable base  
can cause the product to fall, resulting in serious personal  
injuries as well as damage to the product. Use only a trolley,  
stand, tripod, and bracket or table recommended by the  
manufacturer or sold with the product. When mounting the  
product on a wall, be sure to follow the manufacturer’s  
instructions.  
Use only the mounting hardware recommended by the  
manufacturer.  
21.Careful move— When relocating the product placed on a  
trolley, it must be moved with the utmost care. Sudden stops,  
excessive force and uneven floor surfaces can cause the product  
to fall from the trolley.  
22.Panel protection—The LCD panel used in this product is  
made of glass.  
Therefore, it can break when the product is dropped or  
impacted upon by other objects. Be careful not to be injured by  
broken glass pieces in case the LCD panel breaks.  
23.Pixel defect—The LCD panel is a very high technology product, giving you finely detailed pictures.  
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.  
Please note that this does not affect the performance of your product.  
For added protection for this television equipment during a  
lightning storm, or when it is left unattended and unused for long  
periods of time, unplug it from the wall outlet and disconnect  
the antenna. This will prevent damage to the equipment due to  
lightning and power-line surges.  
An outside antenna system should not be located in the vicinity  
of overhead power lines or other electric light or power circuits,  
or where it can collide with such power lines or circuits. When  
installing an outside antenna system, extreme care should be  
taken to keep from touching such power lines or circuits, as  
contact with them might be fatal.  
3
 
I
IMPORTANT INFORMATION  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO  
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
The exclamation point within a triangle is intended to alert the user to the  
presence of important operating and maintenance (servicin g) instructions in  
the literature accompanying the product.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
The lightning flash with arrowhead symbol, within an equilateral triangle, is  
in ten d ed to aler t th e u ser to th e p r esen ce of un in su lated “d an ger ou s  
voltage” with in th e p roduct’s en closur e th at may b e of su fficien t ma gnitude  
to constitute a risk of electric shock topersons.  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
II  
SAFETY TIPS  
Please read and follow the safety tips listed below to ensure the equipment is free  
from damage, and to ensure that no injury will occur as a result of improper use.  
z
z
z
z
z
z
z
Do not insert any object, especially metal or liquids, into the TV.  
Do not place any objects containing water or any other liquid on top of the TV.  
Do not place the unit in direct sunlight, near heaters or in extremely dusty or humid locations.  
Do not install this system outdoors or otherwise expose it to the elements.  
Do not place heavy objects on top of the TV.  
If the power cord is damaged or frayed in any way, electrical shock and/or fire may result.  
Please do not place objects on the power cord, and keep the cord away from heat-emitting devices. Should  
the power cord become damaged in any way, please contact your dealer for a replacement cord.  
Do not remove the cover of the TV for any reason. If any problems arise with the unit, please contact your  
dealer for service. Removing the covers will void the warranty.  
z
III WARNING  
Before Setting Up  
Do not place the TV on sloped or unstable surfaces.  
z
The TV may fall or tip over.  
Do not place any objects on top of the TV.  
z
If water spills onto the LCD TV or foreign objects get inside it, a short-circuit may occur which could result  
in fire or electric shock. If anyforeign objects get inside the LCD TV, please consult an Authorized Dealer.  
Do not cover the ventilation holes.  
Doing so may cause the LCD TV to overheat, which can cause fire or damage to the set.  
AC Power Supply Cord  
The LCD TV is designed to operate on 100~240 V AC, 50/60 Hz.  
Securely insert the power cord plug as far as it will go.  
z
If the plug is not fully inserted; heat may be generated which could cause fire. If the plug is damaged or the  
wall socket plate is loose, they should not be used.  
Do not handle the power cord plug with wet hands.  
Doing so may cause electric shocks.  
z
4
 
Do not do anything that might damage the power cable. When disconnecting the power cable, hold  
the plug, not the cable.  
z
Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully  
pull the power cable. Doing so may cause damage to the power cable, which can cause fire or electric shock.  
If damage to the cable is suspected, have it repaired at an Authorized Service Center  
If the LCD TV is not in use for a long period of time, unplug the power cord from the wall outlet.  
If problems occur during use  
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected  
from the LCD TV, unplug the power cord immediately.  
z
Continuous use of the Display under these conditions might cause fire or permanent damage to the unit.  
Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized  
personnel are strongly discouraged due to its dangerous high voltage nature.  
If water or foreign objects get inside the TV, if the TV is dropped, or if the cabinet becomes  
damaged, disconnect the power cord plug immediately.  
z
A short-circuit may occur, which could cause fire. Contact an Authorized Service Center for any repairs that  
need to be made.  
IV CAUTION  
When using the LCD TV  
To turn off the main power, be sure to remove the plug from power outlet. The power outlet socket should be  
installed as near to the equipment as possible, and should be easily accessible.  
Be sure to disconnect all cables before moving the LCD TV.  
z
Moving the Display with its cables attached might damage the cables, which, in turn, can cause fire or electric  
shock.  
z
Disconnect the power plug from the wall outlet as a safety precaution before carrying out any  
cleaning.  
Electric shocks can result if this is not done.  
Clean the power cable regularly to prevent it from becoming dusty.  
z
Built-up dust on the power cord plug can increase humidity, which might damage the insulation and cause  
fire.  
Unplug the cord from the wall outlet and clean it with a dry cloth.  
z
z
z
z
z
z
z
Do not insert any objects or liquids into the unit.  
Do not expose the unit to water or moisture, or otherwise to the elements  
Do not open the unit for any reason. Doing so will void the warranty!  
Unplug the unit if it will not be used for an extended period of time  
Avoid placing the unit near sources of heat  
Avoid placing the unit in direct sunlight  
In any event, if any problems arise, contact your dealer immediately!  
0871 712 1312  
0.10 £ / mn)  
5
 
2. INTRODUCTION  
Congratulations on your purchase of a THOMSON LCD TV. Your LCD TV will provide you with many years  
of enjoyment no other LCD TV can match. It is compatible with today’s current NTSC, PAL and SECAM systems,  
as well as tomorrow’s DTV standards. This TV is extremely easy to use and features high performance picture  
quality. The LCD TV is extremely versatile; it can be mounted on a wall or table stand, and it can be used in any  
ambient light environment.  
This manual will explain how to use your LCD TV, as well as its features, benefits and other important information.  
Please be sure to read this manual before installing or operating your LCD TV, especially the safety precautions!  
I
SUPPLIED ACCESSORIES  
Make sure the following accessories are provided with the product.  
User Manual(IB) (x1)  
Remote Control (x1)  
Power Cord for European Type (x1)  
Power Cord for UK Type (x1)  
RF Coaxial Cable  
D-Sub to Component Cable  
Size AAA Dry Battery (x2)  
Note: The AC Power cord type is different in  
different territories  
.
6
 
II  
PREPARATION  
Using the Remote Control  
Use the remote control by pointing it towards the remote  
sensor window of the set. Objects between the remote control  
and sensor window may prevent proper operation  
Cautions regarding use of remote control  
z
Do not expose the remote control to shock. In addition,  
do not expose the remote control to liquids, and do not  
place in an area with high humidity.  
z
z
Do not install or place the remote control under direct  
sunlight. The heat may cause deformation of the unit.  
The remote control may not work properly if the remote  
sensor window of the main unit is under direct sunlight or  
strong lighting. In such a case, change the angle of the  
lighting or LCD TV set, or operate the remote control  
closer to the remote sensor window.  
Batteries for the Remote Control  
If the remote control fails to operate the LCD TV functions, replace the batteries in the remote control.  
Open the battery cover.  
Insert batteries (size-AAA batteries, Replace the cover and slide in reverse  
supplied with product).  
until the lock snaps.  
(Slide the cover while pressing  
down.)  
(Place the batteries with their  
terminals corresponding to the (+)  
and (–) indications in the battery  
compartment.  
Precaution on battery use  
Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.  
z
z
z
z
z
Place batteries with their terminals corresponding to the (+) and () indications.  
Only use the battery types specified.  
Do not use rechargeable batteries.  
Different types of batteries have different characteristics. Do not mix batteries of different types.  
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old  
batteries to leak chemicals.  
Do not expose batteries to excessive heat, throw them in a fire, recharge them or try to open them, as this could cause  
them to leak or explode.  
z
z
z
Remove the batteries from the remote control if you are not using it for a long period of time (several weeks).  
Remove batteries as soon as they are non-operable. Chemicals that leak from batteries can cause a rash. If chemical  
leakage is found, wipe with a cloth.  
z
z
The batteries supplied with the product may have a shorter life expectancy due to storage conditions.  
If the remote control is not used for an extended period of time, remove the batteries from the remote control.  
7
 
3. GETTING STARTED  
Switching on  
Follow the instructions on this page on how to switch on your TV set and the remote control before going on to following  
pages describing how to use the remote control and the channel set-up procedure.  
1. Connect the female plug to AC power input of the set.  
2. Connect the male plug to the wall outlet as  
illustrated.  
Equipment for the UK is supplied with a mains cablefitted with a  
moulded plug.  
This plug contains safety components and must not be replaced  
by one sold by general retailers. It is fitted with a fuse that  
protects your television.  
If your set has stopped working, the fuse may have blown. If it  
has, replace it with an identical ASTA or BSI certified (BS1362)  
5-amp fuse.  
3. Connect the outside aerial or cable network to the  
socket at the back of the TV set.  
The aerial socket (75 Ohms - VHF / UHF / cable) can beused  
for connecting an external aerial or other equipment fitted with a  
modulator (video recorder, satellite receiver, etc.).  
We recommend that you do not connect other equipment (video  
recorder, satellite receiver, etc.) to your TV set to begin with, so  
as not to complicate the set-up procedure with the additional  
steps involved. Connect them when you have finished setting up  
the channels by referring to page 21 of this manual.  
4. Switch the TV on by pressing the on/off button on the  
right side.  
You will find a description of how to use the remote control on  
page 9. Then go to page 11 for information on the initial set-up,  
or to page13 for information on manual set-up (if the channels  
have already been set up on your TV).  
8
 
Getting started  
Remote control TV functions  
Most of your television’s functions are available via the menus that appear on the screen .The remote control  
supplied with your set can be used to navigate through the menus and to configure all the general settings.  
This page contains the description of the remote control.  
Standby / quit standby  
.
DVD  
VCR  
TV  
To access DVD mode.  
To access VCR mode.  
To access TV mode.  
Press this button to control the television.  
Light  
To provide information:  
- it lights up when you press a button  
- it indicates the status when the remote control is  
being programmed (see page 10)  
- if the batteries are run down, it flashes when you  
press a button.  
To control the volume.  
This function is also available in VCR and DVD modes.  
To switch the sound off and back on again.  
RETURN To return to the previous menu or the previous program  
PR+/PR- To change channels  
EXIT  
To exit a menu  
MENU  
To access the OVERVIEW menu  
To select menu options  
To set functions, change values, enable and disable  
functions, and to select the picture format (In TV, AV and  
PC mode)  
OK  
To confirm a selection.  
Coloured buttons:  
PRESETS (red button) picture preset settings  
Zzz/LIST (green button) sleep timer setting  
INFO  
(yellow button) status information  
(blue button) disabled in TV mode  
(purple button) Teletext  
GUIDE  
TEXT  
The coloured buttons can also be used for operating Teletext.  
0-9 To select a channel by its number.  
Single digit entry is the default so in the case of channel numbers with two  
digits, press 0 to display “--”, then enter the channel number.  
AV  
To select an appliance connected to an AV socket.  
9
 
Using the remote control for other equipment  
The remote control supplied with your set can be used for other equipment, such as video recorders, PC or DVD  
players. This page provides information concerning the remote control’s use with these types of equipment.  
VCR  
DVD  
VCR  
DVD  
Press the VCR button  
Press the DVD button  
On/Standby  
On/Standby  
MENU  
To display the main menu  
Vertical scrolling in menus  
Horizontal scrolling in menus  
To confirm an action  
To display the main menu  
Vertical scrolling in menus  
Horizontal scrolling in menus  
To confirm an action  
OK  
EXIT  
0-9  
To close a menu  
To directly access channels or enter  
numeric values  
To change channels  
To select AV input  
Rewind  
To close a menu  
To enter numeric values or select options  
in menus  
PR+/PR-  
AV  
REV  
To select  
Rewind  
PLAY  
FWD  
STOP  
PAUSE  
REC  
Play  
Fast forward  
Stop  
Pause picture  
Record  
Play  
Fast forward  
Stop  
Pause picture  
Programming the remote control  
Automatic code search  
This method can be used to automatically find the most appropriate code protocol for your appliance.  
1. Switch on the appliance you wish to use the remote control with.  
2. Press the relevant button for this appliance on the remote control, and while holding this button down, press  
the  
standby button until the remote control light comes on. Release the two buttons.  
3. Point the remote control at the appliance and press PLAY. Wait until the light stops flashing. If the appliance has  
not gone into standby mode after five seconds, press the PLAY button again to continue the search for the next  
set of codes.Repeat this operation until the appliance goes into standby mode. There are 20 sets of codes.  
4. When the appliance goes into standby mode, press the standby button on the right up side to switch it on  
again. Then press the REV button to put it back in standby mode, and if necessary, keep pressing until the  
appliance goes into standby.  
5. Press the STOP button and hold it down until the remote control light goes off.  
Note: you can cancel the programming operation at any time by pressing the EXIT button.  
Manual programming  
This method involves carrying out a manual search for the code to be used for controlling your other appliances.  
1. Switch on the appliance you wish to use the remote control with.  
2. Press the relevant button for this appliance on the remote control, and while holding this button down, enter  
one of the codes relevant to your make of appliance (there is a list of codes at the end of this manual). If the  
remote control light flashes you have entered the wrong code or it is not possible to program the remote control.  
3. Point the remote control at the appliance and press the relevant button (VCRor DVD). Press the standby  
button. If the appliance does not go into standby mode, try another code.  
Depending on the year of manufacture and the type of appliance, some functions may not be available.  
Certain codes may cover more functions than others. Test the functions you can control and, if appropriate, try  
other codes.  
Note here the code(s) which work best.  
VCR  
DVD  
When you change the remote control’s batteries, remember to reprogram it.  
10  
 
4. CHANNELS SET-UP  
Note :If you use the device as LCD Monitor function not a TV, you may skip the chapter.  
Initial set-up  
# AUTOMATIC INSTALLATION  
Return  
Standard  
Start  
Frequency  
Programmes found  
Initial set-up involves selecting all the settings required  
to be able to search for and store all the channels you  
can receive.  
EURO…  
Running…  
150.75MHz  
02  
Make sure that the television is switched on and follow  
all the steps in turn specified on this page.  
1
.
When you first switch the TV set on, the language selection menu appears.  
Choose which language you want the menus to appear by using the ¿ / À buttons.  
When you select a language, it is applied to the menus immediately.  
2
.
.
Confirm with OK. Countries menu will come out and a list of countries will appear.  
3
Select the relevant country by using the ¿ / À buttons.  
This is the country you are in, or the country whose channels you want to receive if living near its borders.  
4
5
.
.
Confirm with OK. The AUTOMATIC INSTALLATION menu will display.  
The Standard option is selected.  
Select a suitable standard using the ½ / ¾ buttons.  
Note: the following standards are available to choose from: UK for the UK and Ireland, FR for Franceand Luxembourg,  
DK for Eastern Europe, the Middle East and Asia, EURO for Western Europe, Australia and New Zealand.  
6
.
Then select the Start option by using the À button and press OK to start the search.  
During this time the message “Running” appears next to the Start option and the Frequency and PR  
found(Programme found) options appear, informing you of the process of installation procedure.  
If you press the EXIT button before the end of channel searching, the channels already found are stored.  
Once the search has ended the ORGANISER menu appears (see following page).  
Note : You may subsequently return to AUTOMATIC INSTALLATION menu by selecting the Automatic  
installation line in the INSTALLATION menu.  
11  
 
Organiser  
# ORGANISER  
By using this menu you can change the channels order  
arranged during automatic set-up, name and rename  
channels, delete duplicate channels or those with poor  
reception quality.  
Return  
Select programme  
Swap with programme  
Change pr. name  
Delete programme  
01  
--  
BBC1  
01  
Follow the help messages at the bottom of the screen  
and refer to a TV programme guide to help identify the  
channels.  
Arranging channels in order  
The Select programme line is selected.  
Display the channel number to be changed using the PR+/PR- buttons or the 0-9 keys.  
Select the option Swap with programme. Enter the new programme number using the 0-9 keys.  
Press OK to confirm. When you successfully finish the swap, the bottom help line will show  
The programmes have been swapped“ message. Follow the same procedure for the other channels.  
Deleting channels  
The Select programme line is selected.  
Display the channel number to be deleted using the PR+/PR- buttons or the 0-9 keys.  
Select the Delete programme option and press the OK button to delete the channel.  
Once this channel has been deleted the bottom help line will show “ The programme has been  
deleted“ message.  
Note : you can use AUTOMATIC UPDATE menu (from Installation menu) to restore the deleted programme  
Naming or renaming channels  
The Select programme line is selected.  
Display the number of the channel whose name you want to change using the PR+/PR- buttons.  
The relevant channel appears. Select the Change pr. name option and press the ¾ button to place the cursor  
on the first character.  
Using the ¿ / À buttons, select a character from the list, which includes letters from the alphabet, numbers  
between 0 and 9, the characters +,. and space. Go on to the next character or back to the previous character  
using the ½ / ¾ buttons and start the procedure again.  
Press OK to confirm. Names can have a maximum of six characters.  
Press EXIT to close the menu.  
Note : You may subsequently return to ORGANISER menu by selecting the Organiser line in the  
INSTALLATION menu.  
12  
 
Manual channel set-up  
Follow the procedure given on this page if you find that some channels have not been stored during the initial set-  
up. This can happen if you are setting up cable network channels. Setting up channels manually requires every  
setting for a particular channel to be entered, one at a time.  
Display the OVERVIEW menu by pressing the  
MENU button.  
# MANUAL INSTALLATION  
Return  
Standard  
Frequency  
Programme name  
Fine-tuning  
Select the Installation option and press OK to  
confirm.  
EURO…  
150.75MHz  
BBC2  
Select the relevant country and press OK.  
------|----------  
Store on programme  
Decoder  
Teletext char. set  
02  
Select the Manual Installation option from the  
INSTALLATION menu and press OK to confirm.  
1…  
1. Select the Standard option and then the relevant standard for your country using the ½ / ¾ buttons.  
Note: the following standards are available to choose from: UK for the UK and Ireland, FR for Franceand Luxembourg,  
DK for Eastern Europe ,the Middle East and Asia, EURO for Western Europe, Australia and New Zealand.  
2. Select the Frequency option. Use the ½ or ¾ button to start the search in descending or ascending order.  
When a channel is found, pictures appear.  
Note : If the channel name is found,it is displayed next to Programme name option.  
3. If the picture is not clear you can adjust the setting. You do this by selecting the Fine tuning option and  
adjusting it with the ½ / ¾ buttons.  
4. If the channel is encrypted and you want to connect a decoder, select the Decoder option and check the box  
by pressing the OK button.  
5. Then select the Teletext char. set option and choose the character set that will be used for Teletext on this  
channel using the ½ / ¾ buttons. The following character sets are available:  
1 : Western Europe  
2 : Eastern Europe  
3 : Turkish and Greek  
4 : Russian and Bulgarian  
5 : Arabic  
6 : Farsi  
The character set selected determines how characters are displayed on Teletext screens.  
6. Select the Store on programme option to assign a number to the channel. Enter the number using the  
numeric buttons. Press the OK button to confirm.  
Important: As soon as you change a setting in the MANUAL INSTALLATION menu, the channel number starts  
flashing under the Store on programme option .To confirm your change you must select the Store on programme  
option and press OK. If you do not confirm the chang, it will be cancelled when you change channel or put the television  
into standby mode.  
Repeat this procedure (2 to 6) to find other channels.  
Automatic update:  
Auto update allows you to set up channels just launched or any channels that are missing or wrongly set up.  
You can access Automatic update menu by selecting the line inside the INSTALLATION menu.  
Return: return to the INSTALLATION menu  
.
Standard: Select the relevant standard for your country using the ½ / ¾ buttons.  
Note: the following standards are available to choose from: UK for the UK and Ireland, FR for Franceand Luxembourg,  
DK for Eastern Europe ,the Middle East and Asia, EURO for Western Europe, Australia and New Zealand.  
Start: Press OK to start the auto update function  
The Frequency is incrementing during the progress of the searching. New pr. found” is incremented each time  
when a PR, which is not already installed, is found. When the highest frequency is reached, the auto update fuction  
will stop. Or if you press EXIT button, you will also stop the auto update fuction.  
13  
 
5. OPERATION  
General operation  
Switching the TV set on and off  
To switch the TV set on, press the  
button located on the right side of the set.  
When the set is on, the indicator on the front is green.  
Standby mode  
Press the  
button on the screen right side of TV or on the remote control.  
The TV set remains powered up, but with low energy consumption.  
When the TV set is in standby mode, the indicator on the front is red.  
Quitting standby mode  
- Press the  
or any numeric button on the remote control,  
- press the PR+/PR- buttons to switch on the television at the last channel or AV programme you were watching,  
- press the AV button to switch the television on at the last AV programme you were watching.  
Volume  
Volume control: use the VOL + / - buttons on the right side of the TV set or press the same buttons on the  
remote control to increase or decrease the volume.  
Sound mute: press the  
restore it.  
button to temporarily mute the sound. Press this button again or the VOL+ button to  
Displaying status information  
In TV mode, press the yellow button (INFO) on the remote control to display the number and name of the  
channel you are watching, the type of sound, the zoom or format type, sound mute status and the sleep  
timer status (if active).  
TV lock message is displayed if the function is activated under the PREFERENCES menu.  
When you switch on the television or change channels, the number and name of the channel are displayed if you  
entered its name under the ORGANISER menu.  
In PC and PIC(see page 21) modes, press the yellow button (INFO) on the remote control to display the  
Resolution ,Vertical and Horizontal frequency.  
Accessing channels  
Using the numeric buttons:  
- for channels 1 to 9, press the corresponding button.  
- for channels 10 to 99, press the 0 button to display “--“, then enter the two digits.  
Using the PR+/PR- buttons: scroll through the channels.  
AV programmes are not included in the cycle unless you use the buttons on the right side of the TV set.  
Accessing AV programmes  
Press the AV button to display the last selected audio-visual programmes and scan through the other audio-visual  
programmes.  
AV selections loop: AV1, AV1RGB, AV2, AV2-S, YCrCb, YPrPb, DVI, PC  
14  
 
Zoom  
In TV mode, you have the option of changing the display format and using the zoom function via the ½ / ¾  
buttons. Here is selections of Zoom:  
4/3 Format - picture in 4/3 format  
Zoom 14/9 - picture in 14/9 letterbox format  
Zoom 16/9 - picture in 16/9 letterbox format  
Zoom 16/9 up - picture in 16/9 letterbox format moved up for subtitles  
Cinerama - Cinerama  
16/9 Format - picture in 16/9 format  
Note : The Zoom type can’t be change when menu appears on thescreen. In Teletext mode, the screen alway 4/3 format  
but if exiting the Teletext mode, the screen will return theformer Zoom level.  
When user changes the zoom format, the zoom status will appear temporarily at the bottom of the screen.  
Panning function for Zoom  
In 14/9 Zoom, 16/9 Zoom, or 16/9 Zoom up, user can shift the picture up and down temporarily by using  
button and the panning icon will display.  
When the picture reach the upperest positon for the zoom level, the panning icon will show :  
When the picture reach the lowest positon for the zoom level, the panning icon will show :  
Last programme  
Press the RETURN button to return to last watched programme.  
Freeze  
Press OK button in TV mode to freeze the picture. Press again OK button to unfreeze the picture.  
15  
 
Adjusting the sound  
; SOUND  
Display the OVERVIEW menu by pressing the  
MENU button.  
Return  
Preset  
Standard…  
Balance  
Sound type  
Auto. volume leveling  
Internal speakers  
Advanced settings  
------|-----------  
Stereo…  
Select the Sound option and press OK to confirm.  
The SOUND menu appears with the following  
options:  
;
Return  
Preset  
:
go back to OVERVIEW menu  
use the ½ or ¾ button to select the appropriate setting (Standard, Film, Voice, Music and  
:
Personal) for the programme you are watching.  
Personal option contains the values you have defined for Equalizer settings.  
Balance: use the ½ or ¾ button to balance the sound between the right and left speakers.  
Sound type: this option is used to select the appropriate sound type(Automatic, Stereo, Sound 1, Sound 2,  
Sound 3, Nicam, Mono).  
The available options depend on the programme you are watching.  
The table at the bottom of this page indicates the sound types available for each type of broadcast.  
Auto. volume leveling:. Tick the box using OK button if you want to keep the same sound level on all the  
channels.  
Internal Speakers: the TV set’s speakers are enabled by default - the box is checked.  
You can connect amplified speakers or an amplifier to the TV LCD (see the “Other information” chapter).You  
can then get the most out of the sound using all the speakers or you can disable the internal speakers.  
Uncheck the box to do this, by pressing OK to confirm.  
Advanced Settings Press OK to access following options.  
:
Treble ,Mid Treble, Medium, Mid Bass, Bass (Equalizer)  
adjustments by using the ½ / ¾ buttons.  
These settings are automatically stored under Personal in the Preset option.  
:
select each band in turn and make the necessary  
Dolby Virtual  
Surround effect  
Press EXIT to close the menu or select the option Return and press OK to return to the SOUND menu.  
:
Check the box by pressing OK to enable Dolby Virtual effect setting.  
:
adjust the surround effect as required using the ½ / ¾ buttons.  
Broadcast  
Mono  
Options  
Manufactured under license from  
Dolby Laboratories.  
Automatic, Mono  
Nicam, Mono  
Nicam mono  
Nicam / IRT stereo  
Bilingual Nicam  
Bilingual IRT  
AV  
“Dolby”, and the double-D symbol are  
trademarks of Dolby Laboratories.  
Stereo, Mono  
Sound 1, Sound 2, Sound 3  
Sound 1, Sound 2  
Stereo, Sound 1, Sound 2  
16  
 
Adjusting the picture  
The PICTURE menu can be used to adjust the current settings, to apply preset settings and define your own  
preferred settings.  
ÕPICTURE  
Display the OVERVIEW menu by pressing the MENU  
button.  
Return  
Preset  
Studio…  
Brightness  
Contrast  
Colour  
Sharpness  
Tone  
------|-----------  
------|-----------  
------|-----------  
------|-----------  
Warm…  
Select the Picture option and press OK to confirm.  
The PICTURE menu appears. It offers the following  
options:  
Other settings  
Return use the buttons to go back to the OVERVIEW menu  
:
Preset: use the ½ / ¾ buttons to select from the preset settings offered (Standard, Film, Sport, Studio,  
Personal) the one which suits best the programme you are watching.  
The Personal option contains the values you have defined for Brightness, Contrast, Colour and Sharpness  
settings.  
Brightness, Contrast Colour, Sharpness: adjust these settings as required using the ½ / ¾ buttons.  
,
Brightness, Contrast, Colour and Sharpness settings are automatically stored under Personal in the Preset  
option  
Preset, Colour and Sharpness options are not displayed in PC mode.  
Tone: this options controls colour temperature.  
Use the ½ / ¾ buttons to select between Cold, Neutral and Warm.  
Other settings  
:
This option is not displayed in PC mode.  
Press OK to access following options.  
Return  
Noise Reduction  
You can choose between Off, Low, Medium and High.  
Black Expand adjust these settings as required using the ½ / ¾ buttons.  
:
use the buttons to go back to the PICTURE menu  
:
adjust the noise reduction strength by using the ½ / ¾ buttons.  
:
You can choose between Off, Low, Medium and High.  
Auto format: by default, checkbox is on  
The TV (16/9) adapts to the broadcast picture format if the equipment connected via a Euro-AV (scart) socket  
provides a control signal.  
With AV2 and Component YCrCb, Auto format is not displayed.  
Tint This option is only available for NTSC audio-visual sources.  
:
Adjust the tint of the picture using the ½ / ¾ buttons.  
If the device is in PC mode you can access following functions in Picture Menu.  
Phase, Synchronization, V-Position, H-Position  
Select the desired option and adjust as required by using the ½ / ¾ buttons.  
Press EXIT to close the menu.  
Note : pressing PRESETS button (Red) in TV or PC mode out of the menus opens the PICTURE menu with the  
Preset linehighlighted.  
17  
 
Setting the Preferences  
The Preferences menu can be used to set your preference including Eco mode, Permanent PR, Back light,  
Sleep timer, TV Lock and Language.  
PREFERENCES  
Return  
Eco mode  
Permanent pr. number  
Backlight  
Sleep timer  
TV lock  
Display the OVERVIEW menu by pressing the  
MENU button.  
Normal…  
0:00  
Select the Preferences option and press OK to  
confirm.  
Language  
English…  
The PREFERENCES menu appears. It offers the  
following options  
Note: TV, PC and DVI mode have thesame Preferences Menu  
Return use the buttons to go back to the OVERVIEW menu.  
:
Eco mode: When this function is on, the LCD TV will go to stand by automatically after ten minutes without  
video signal. Tick the box by pressing OK to activate the function.  
If in PC or DVI mode, this Eco mode selection will enable the PC power management function.  
Permanent pr. number  
watching  
If the signal source is AV, the AV OSD tag will be displayed permanently.  
:
tick the box by pressing OK to permanently display the number of the channel you are  
.
Back light  
Using the ½ / ¾ buttons you can choose between Soft, Normal and Bright.  
Sleep timer  
:
this option allows to adjust the backlight of your LCD TV.  
:
1. Select the Sleep timer option.  
2. Set an automatic shut-off time (from 0 to 4 hours in 15-minute intervals) by using the ½ / ¾ buttons.  
Set the time to 00:00 to disable this function.  
TV Lock  
This function allows the parents:  
Either to lock the LCD TV set by putting it into to standby mode or to choose a programme their children will be  
able to watch until the sleep timer expires.  
Tick the box by pressing OK to activate the TV lock.  
When you turn on the function, we suggest taking remote control away. In this case, children can only adjust the volume or  
switch the LCD TV off.  
Once in standby mode, TV LCD can then only beswitched on using the remote control.  
Language  
Using the ½ / ¾ buttons select your preferred language for menus.  
Available languages are : English, French, German, Italian, Spanish .  
Press EXIT to close the menu.  
Note: pressing Zzz (Green) in TV mode out of the menus opens the PREFERENCES menu with the Sleep timer line  
highlighted.  
18  
 
Teletext  
The Teletext service is available in many countries under a variety of names (TOP Text, Fastext, FLOF text,  
Videotext). It is provided as a free service by television broadcasters. This service provides a real wealth of  
information, available at any time, on weather, sports results, news, games, etc. The information is presented in  
pages or organised in topics specified in colour on the screen and you can access this information by simply  
pressing the buttons of the relevant colour on the remote control.  
Accessing Teletext  
Press the TEXT button on the remote control. Teletext will display the last page selected, or if you have changed  
channel, the index page.  
To display a page, enter its 3-digit number or use the PR+/PR- buttons. The page appears after a few moments.  
Navigation bar  
The navigation bar, located at the bottom of the screen, provides access to the next three pages and the previous  
page by pressing the relevant colour button on the remote control.  
AS the picture for example:  
Press red to page 201; Press green to page 202; press yellow to page 203; press blue to page 199  
Press the MENU button to display the navigation bar and access the following functions:  
STOP: this function is used to stop pages from following on in succession. Press the red button to select this  
function. The word STOP (or an icon) appears in place of the page number.  
Press the red button again to allow the pages to follow on again.  
??? (hidden answers): press the green button to reveal a hidden answer (for example, in games). Press the green  
button again to hide the answer.  
ZOOM: press the yellow button:  
1st key press: page is zoomed in and displays rows 1 to 12  
2nd key press: the page is zoomed and displays rows 13 to 24  
3rd key press: the page returns normal size and displays full page.  
MIX (mixed display): press the blue button to display Teletext against a transparent background. Press this button  
again to return to normal display.  
Changing the character set temporarily  
You can change the character set used for Teletext, if the existing one is not suitable for the channel you are  
watching.  
You do this by pressing the MENU button to display the navigation bar.  
Then press OK to display the number of the character set currently being used in place of ???.  
Use the green button to select another character set.  
The character set selected in the INSTALLATION menu will be restored when the TV set is switched off or  
enters standby mode, or when you change channels.  
Press the EXIT button to quit the Teletext function.  
Note : In teletext mode, the Vol+/Vol and Mute are still functional but on screen will not show volume bargraph and mute  
symbol  
Other Teletext functions  
Newsflash  
When a newsflash is detected, MIX is replaced by N in the navigation bar. Press the blue button to display the  
newsflash. In the case of an update, the Teletext function is enabled and displays the new information.  
This function is disabled if TV changes the programme, enters standby mode or is switched off.  
Press the EXIT button to quit the Teletext function and return to TV mode.  
19  
 
Subtitles  
Some channels provide subtitles for some of their programmes. The number of the relevant pages is specified on  
the Teletext index page.  
To display subtitles, enable the Teletext function, find the number of the page displaying the subtitles and enter it.  
Once the relevant page is found, the subtitles appear in the TV picture. The navigation bar disappears after a  
couple of seconds. To display the top bar, press the purple (TEXT) button.  
Press the EXIT button to quit the Teletext function.  
Direct access to subpages  
Some information is spread across more than one page (“----“ displayed next to the page number). To access  
subpages, press the ½ or ¾ button.  
Enter the subpage number(4 digits) by using the numeric buttons.  
To cancel subpage mode, please select a new page number by pressing PR+/PR-, press the ½ or ¾ button, or  
change channels.  
Fastext  
If Fastext is available, direct access to previous and subsequent pages is replaced by coloured bars (red, green,  
yellow and blue), which provide links to the topics you can access by pressing the relevant colour button. Other  
topics accessible in the same way can also be displayed. Press the MENU button to go from these links to the  
navigation bar.  
20  
 
6. OTHER INFORMATION  
PIC (Picture in Computer Mode)  
When you have connected the PC to TV set (in PC mode), you can open the function by pressing PR+/PR- and  
you will watch programme displayed on the top right of the screen.  
The picture size is not adjustable, you may move the picture position from top left, top right, bottom left, bottom  
right by pressing the ¿ / À key.  
The sound will always come from the programme inside the PIC no matter whether the PC is playing video file;  
however, inside PIC there is no overview function for it but you can change the video input type such AV1,  
AV2, AV2-S etc.  
PIC is 4/3 picture format and the programme number will permanently display in yellow colour.  
You may choose the channel of picture by pressing numeric number (0-9).  
Sockets: at the bottom of the TV back side (From right to left)  
SCART socket AV1 (input-output)  
This socket can be used to connect a range of equipment, including video recorders,  
camcorders (VHS or 8-mm), decoders, satellite receivers, DVD players, games  
consoles or appliances producing an RGB signal.  
To display images from the connected appliance, select AV1 using AV button on the remote  
control.  
For some appliances (connected to the SCART socket), this selection is made automatically.  
For appliances producing an RGB signal, select AV1 RGB.  
RF signal (Input) for the TV antenna or cable system using defined broadcasting  
standards such as BG (Euro), LL' (FR), I (UK) and DKK’(DK).  
Audio stereo jack socket (output) This can be used to connect a stereo amplifier, a  
hi-fi system or amplified speakers (see below).  
Audio (R/L) and video (CVBS) CINCH sockets AV2 (input)  
These can mainly be used to connect camcorders (VHS or 8-mm format).  
To display images from the connected appliance, select AV2 using AV button on the remote  
control.  
S-video socket AV2 and Audio (R/L) (input)  
These can mainly be used to connect camcorders (S-VHS or Hi 8 format).  
To display images from the connected appliance, select AV2-S using AV button on the  
remote control  
CVBS and S-Video share the same L/R audio input.  
YCrCb component and Audio (R/L) (input)  
YCrCb is for interlacing signal and mainly be used to connect DVD player.  
To display images from the connected appliance, select YCrCb using AV button on the  
remote control.  
21  
 
YPrPb (for Video), D-Sub (forPC) and Audio (input)  
LCD TV uses D-Sub (15 pin) connector for YPrPb signal source and the D-Sub also  
can be used for PC input.  
Note: This model only supplies D-Sub to component line  
YPrPb is for progressive signal and mainly be used to connect DVD player or HDTV.  
Connect the stereo sound input jack on the back of the LCD TV (near the D-sub  
connector) to the audio output terminal of equipment.  
To display images from the connected appliance, select YCrCb using AV button on the  
remote control.  
DVI and DVI Audio input(R/L)(input)  
DVI is digital video interface for PC and Video use but LCD TV DVI connector main  
function is for PC input only  
Connecting active speakers or an amplifier (using a jack / CINCH cable not provided).  
The audio stereo jack socket located on the back of the LCD TV set can be used to connect active speakers (with  
a built-in amplifier) or an amplifier.  
Connect the left and the right speaker to the stereo jack socket using a jack / CINCH cable (not provided).  
To connect an amplifier, you should connect the LCD TV set’s stereo jack socket to the amplifier’s L and R inputs  
using a jack / CINCH cable (not provided).  
Connecting headphones  
Use the relevant socket on the right side of the LCD TV set to connect headphones or stereo earphones.  
Connecting a video recorder  
To obtain optimum picture quality, use a SCART cable. However, you can also connect a video recorder to the  
television using the aerial socket.  
If you connect a video recorder only via the aerial socket (without using the SCART socket), switch it on and play  
a tape.  
Then search for the video recorder’s relevant channel (refer to the relevant section).  
If you connect a video recorder via the aerial socket, you should assign channel 99 to it in order to improve the  
picture quality when tapes are being played and in pause mode. However, we recommend you connect your video  
recorder via the SCART socket, as it provides better picture and sound quality.  
22  
 
Connecting a Computer  
Method A :  
Connect the D-sub signal terminal on the back side of the LCD TV to the output of  
PC equipment through min D-sub 15 pin cable.  
Connect the stereo sound input jack on the back of the LCD TV to the audio output  
terminal on the computer.  
To display images from the connected computer, select PC using AV button on the remote  
control  
Method B :  
Connect the DVI signal terminal on the back side of the LCD TV to the output of PC  
equipment through min DVI cable.  
Connect the stereo sound input jack (Audio input near DVI connector) on the back of  
the LCD TV to the audio output terminal on the computer.  
To display images from the connected computer, select DVI using AV button on the remote  
control  
Note:  
1.  
The display native resolution is 1024 x 768. If the signal resolution exceeds the native resolution, it may not  
be possible to show fine detail with sufficient clarity.  
2.  
3.  
4.  
5.  
An adapter is required to use the PC cable (D-sub 15P) to connect a Macintosh computer to the set.  
Some PC models cannot be connected to the set.  
There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminals.  
Do not set the horizontal and vertical scanning frequencies for PC signals, which are above or below the  
specified frequency range.  
For more information about external device connections, see the manuals of your external devices.  
23  
 
TROUBLE SHOOTING  
Before you call for service, determine the symptoms and make a few simple checks as shown below.  
TV set:  
SYMPTOMS  
Power does not turn ON  
POSSIBLE CAUSES  
Ensure whether the power plug is securely inserted into the  
receptacle.  
Ensure the LCD TV power is ON (Indicated by the green LED on  
the front of the unit)  
Reception other than those of broadcasting stations can be  
considered.  
z
z
z
There is no picture or sound  
z
z
Check for connection to wrong terminal or for wrong input mode.  
Ensure the communication cable is properly connected between  
the Video Source and the LCD TV.  
There are spots on the screen  
z
Check whether your AV equipments is affected by interference  
from automobiles, trains, high-voltage transmission lines, neon  
signs or other potential sources of interference.  
Check whether all image adjustments have been properly adjusted.  
Check whether screen position and size have been properly  
adjusted.  
Degraded colors or tints  
Improper screen position or size  
z
z
The image appears distorted  
The image is purple  
z
z
Ensure the TV's aspect ratio is properly set.  
Check the "Component" or "RGB" setting in the LCD TV and set  
it for the appropriate signal type.  
The image appears too bright, and  
there is a loss of definition in the  
brightest areas of the image.  
z
z
z
Check whether the contrast setting is too high.  
The DVD player is set for a high-level output.  
The video signal has not been terminated properly somewhere in  
the system.  
The image appears too 'washed out',  
or the darkest areas of the image  
appear too bright.  
z
z
Check whether Brightness is set too high.  
The DVD player may be set at too high a brightness level.  
If “xxx searching” appears, the image  
or signal cannot be produced by  
display.  
z
z
Check the cable for disconnection.  
Check for connection to proper terminal or for proper input  
mode.  
“Out of range” appears  
Remote Control does not function  
properly  
z
z
z
z
z
Check whether the input signal is acceptable to the display.  
Check for incorrect battery orientation.  
Check for dead batteries  
Check for distance and angle from the display.  
Check whether remote control is properly being pointed at the  
display’s receiver.  
z
z
Check for any obstacle between the remote control and the  
display.  
Check that the remote sensor window is not under strong  
fluorescent lighting.  
There is no picture or sound, just  
noise.  
Picture is not clear.  
z
z
z
z
z
z
z
z
Make sure the antenna cable is properly connected.  
Consider whether TV signals are being properly received.  
Make sure the antenna cable is properly connected.  
Consider whether TV signals are being properly received.  
Check whether you have selected “Mute” for Audio setting.  
Make sure the volume is not set to minimum.  
Make sure that headphones are not connected.  
Check cables for disconnection.  
No sound  
24  
 
Antenna:  
SYMPTOMS  
POSSIBLE CAUSES  
The picture is not sharp or the  
picture moves.  
z
z
z
z
z
z
z
The reception may be weak.  
The state of the broadcast may also be bad.  
Make sure the outside antenna is not disconnected.  
Make sure the antenna is facing the right direction.  
Make sure the antenna is facing the right direction.  
There may be reflected electric waves from mountains or buildings.  
There may be interference from automobiles, trains, high voltage  
lines, neon lights, etc.  
The picture is doubled or tripled.  
The picture is spotted.  
z
z
There may be interference between the antenna cable and power  
cable. Try positioning them further apart.  
There are stripes on the screen or  
colors fade.  
Is the unit receiving interference from other devices? Transmission  
antennas of radio broadcasting stations and transmission antennas  
of amateur radios and cellular phones may also cause interference.  
Use the unit as far apart as possible from devices that may cause  
possible interference.  
z
25  
 

Taylor Scale 5742 User Manual
The Singing Machine CD Player STVG 520 User Manual
Toastmaster Mixer TSM10 User Manual
Toshiba Laptop A11 User Manual
Toshiba Personal Computer M10 User Manual
Trane Air Conditioner RLC PRC006 EN User Manual
Triarch Indoor Furnishings 33121 User Manual
Viking Range F20513 User Manual
Vox Music Pedal Satchurator User Manual
Vulcan Hart Electric Steamer VHX24E User Manual