MODEL
VSB207
VIZIO
QUICK
START
GUIDE
PACKAGE CONTENTS
Sub
-
Sub
+
Input
SRS
High Definition Sound Bar
Remote Control
with Battery
Power Adapter w/Cable
This Quick Start Guide
Stereo RCA to 3.5mm
Audio Cable
CONTROLS & CONNECTIONS
Power
Press to turn
Sound Bar
on or off.
Input
Volume + / -
Press to increase/
decrease system
volume.
Press to change
input source
(Input 1, Input 2).
Input
Vol -
Vol +
SUB OUT
INPUT
1
24V DC
SERVICE
INPUT
2
SUB OUT
INPUT 1
24V DC
SERVICE
INPUT 2
Input 2
(Stereo 3.5mm)
Power Port
Service Port
For use only by service technician.
Sub Out Input 1
(RCA) (Stereo RCA)
FIRST-TIME SETUP
1
SUB OUT
INPUT 1
24V DC
SERVICE
INPUT 2
BACK OF SOUND BAR
CHOOSE ONE
Connect the included Stereo RCA to
3.5mm Cable to ONE TV audio output
as shown.
AUDIO OUT
AUDIO OUT
BACK OF YOUR TV*
*Not all TVs have the audio outputs shown above. To connect the Sound Bar directly to your other devices (Blu-ray player, game system, etc) see your device’s user manual.
2
SUB OUT
24V DC
SUB OUT
INPUT
1
24V DC
SERVICE
INPUT
2
3
4
5
Sound Bar is
centered below the
TV.
For the best surround sound experience, position the Sound Bar as shown.*
The Sound Bar should be close to ear level.
6
Power
Turn your TV on, then press the Power button on
the remote to turn the Sound Bar on.
Sub -
Sub +
Press the Input button to switch between audio
sources. For example, if you connected your TV to
Input 1, set the Sound Bar to Input 1.
Setup is complete.
Input
Input
SRS
USING THE REMOTE
Power
Press to turn on or off.
Volume Up
Press to increase
volume.
Mute
Press to mute/unmute.
Sub +
Press to increase
subwoofer volume.
Sub -
Sub +
Sub -
Press to decrease
subwoofer volume.
Volume Down
Press to decrease volume.
Input
SRS
Input
SRS
Press to change input source.
Press to activate
SRS WOW HD.
For best results, point the remote
at the right side of the Sound Bar.
The sensor is located there.
CHANGING THE BATTERY
2
1
Insert a flat-head screwdriver into the slot as shown.
Gently push down on the tab, then press and pull
downward on the battery cover to open.
Replace the old battery with a new CR2032. Be
sure that the + sign on the battery is facing up.
Push the battery cover until it clicks back into place.
CONNECTING A SUBWOOFER
1
SUB OUT
INPUT 1
24V DC
SERVICE
INPUT 2
BACK OF SOUND BAR
TURN BOTH SOUND BAR AND
SUBWOOFER OFF.
CONNCECT AN RCA CABLE* TO
YOUR SUBWOOFER*.
The volume on your Subwoofer
must be manually adjusted. See
your Subwoofer’s user manual for
details on proper operation.
*NOT INCLUDED
WALL MOUNTING THE SOUND BAR
1
Remove the screw from the Sound
Bar stands and rotate as shown.
26 3/4”
(67.95 cm)
Be sure your screws are attached
to wood studs or drywall anchors
(for drywall) or concrete anchors
(for brick/concrete walls). Wall
mounting hardware is not included.
2
If you are unfamiliar with power tools or the layout of electrical wiring in
the walls of your home, consult a professional installer.
Reattach stands using the
included screw.
Mounting hardware not included.
HELP & TROUBLESHOOTING
All VIZIO products include FREE lifetime technical support.
The VIZIO support team is highly trained and is based in the United States.
We can help with:
• Product Setup
• Technical Problems
• Warranty Questions
• And More
Hours of operation:
Monday - Friday: 5 AM TO 9 PM (PST)
Saturday - Sunday: 8 AM TO 4 PM (PST)
Phone: (877) 698-4946 (TOLL-FREE)
Email: [email protected]
Web:
• Press the POWER button on the remote control or on the top of your Sound Bar.
• Ensure the power cord is securely connected.
There is no power.
• Ensure the light on the power adapter is glowing green.
• Plug a different device into the electrical outlet to verify that the outlet is working correctly.
• Increase the volume. Press Volume Up on the remote control or on the top of your Sound Bar.
• Press MUTE on the remote to ensure the Sound Bar is not muted.
• Press INPUT on the remote or on the top of your Sound Bar to select a different input source.
• If you are using a SPDIF/Optical connection, make sure your TV is set to PCM audio output.
There is no sound.
• Your TV may be set to variable audio output. Confirm that the audio output setting is set to FIXED or
STANDARD, not VARIABLE. Consult your TV’s user manual for more detailed information.
• Ensure all cables and wires are securely connected.
I hear buzzing or
humming.
• Connect a different source device (TV, Blu-ray player, etc) to see if the buzzing persists. If it does not,
the problem may be with the original device.
• Connect your device to a different input on the Sound Bar.
ONE-YEAR LIMITED WARRANTY
ON PARTS AND LABOR
Covers units purchased as new in United States and Puerto Rico Only
VIZIO provides a warranty to the original purchaser of a new Product against defects in materials and workmanship for a period of one year of non-commercial usage and ninety (90) days of
commercial use. If a Product covered by this warranty is determined to be defective within the warranty period, VIZIO will either repair or replace the Product at its sole option and discretion.
To obtain warranty service, contact VIZIO Technical Support via email: [email protected] or via phone at 877 MY VIZIO (877.698.4946) from 6:00AM to 9:00PM Monday through Friday and
purchase in the form of a purchase receipt or copy thereof is required to show that a Product is within the warranty period.
Parts and Labor
There will be no charge for parts or labor during the warranty period. Replacement parts and Products may be new or recertified at VIZIO’s option and sole discretion. Replacement parts and Products
are warranted for the remaining portion of the original warranty or for ninety (90) days from warranty service or replacement, whichever is greater.
Type of Service
Defective Products must be sent to a VIZIO service center to obtain warranty service. VIZIO is not responsible for transportation costs to the service center, but VIZIO will cover return shipping to the
customer. PRE-AUTHORIZATION IS REQUIRED BEFORE SENDING ANY PRODUCT TO A VIZIO SERVICE CENTER FOR WARRANTY SERVICE.
Product returns to VIZIO’s service centers must utilize either the original carton box and shipping material or packaging that affords an equal degree of protection. VIZIO Technical Support will provide
instructions for packing and shipping the covered Product to the VIZIO service center.
Limitations and Exclusions
VIZIO’s one-year limited warranty only covers defects in materials and workmanship. This warranty does not cover, for example: cosmetic damage, normal wear and tear, improper operation, improper
voltage supply or power surges, signal issues, damages from shipping, acts of God, any type of customer misuse, modifications or adjustments, as well as installation and set-up issues or any repairs
attempted by anyone other than by a VIZIO authorized service center. Products with unreadable or removed serial numbers, or requiring routine maintenance are not covered. This one year limited
warranty does not cover Products sold “AS IS”, “FACTORY RECERTIFIED”, or by a non-authorized reseller.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED OR DESCRIBED ABOVE. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE PERIOD OF TIME SET FORTH ABOVE. VIZIO’S TOTAL LIABILITY FOR ANY AND ALL
LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER INCLUDING VIZIO’S NEGLIGENCE, ALLEGED DAMAGE, OR DEFECTIVE GOODS, WHETHER SUCH DEFECTS ARE
DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. VIZIO SHALL NOT BE RESPONSIBLE FOR LOSS OF USE, LOSS OF INFORMATION OR
DATA, COMMERCIAL LOSS, LOST REVENUE OR LOST PROFITS, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. THIS WARRANTY IS SUBJECT TO CHANGE WITHOUT NOTICE.
SPECIFICATIONS
Sound Bar: Two High-Efficiency Full-Range
Transducers
Frequency Response (Sound Bar): 90 Hz - 19.5 KHz
Voltage: 100-240 VAC, 50-60 Hz
Inputs: 1 x 3.5mm Stereo Audio
1 x RCA Stereo Audio
Compliances: UL, FCC
Outputs: 1 x RCA Subwoofer Out
Sound Pressure Level: 86 dB
LEGAL & COMPLIANCE
FCC Class B Radio Interference Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such
interference.
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves.This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
IC Statement
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC Radiation Exposure Statement
SRS WOW HD is a trademark of SRS Labs, Inc. WOW
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
HD technologies are incorporated under license from
environment. This equipment should be installed and operated with minimum distance 20cm
SRS Labs, Inc.
between the radiator & your body.
Disposal and Recycling
You must dispose of this product properly, according to local laws and regulations.
Because this product contains electronic components and a battery, it must be disposed
of separately from household waste. Contact local authorities to learn about disposal and
recycling options.
© 2012 VIZIO INC. ALL RIGHTS RESERVED.
120110ST-A
|